DSM Academy : Industry & Entrepreneurship Based Training Institute in Bhopal

All Minor Major ROBOTICS EMBEDDED 1

TEMPERATURE CONTROLLED DC FAN USING MICROCONTROLLER

The main principle of the circuit is to switch on the fan connected to DC motor when the temperature is greater than a threshold value. This can be used in home applications and in CPU to reduce heat.

TIME OPERATED ELECTRICAL APPLIANCE CONTROLLING SYSTEM

Each device will have an on-time and off-time. So the kit will daily switch on the device at the on-time and switch it off when the real time is same to the off time of the device. The appliance is switched on when the user time and real clock time is equal. You have to enter 2 timings. One is “on time” and the other is “off time”.

CLAP SWITCH

A clap switch is an electronic circuit, which controls electrical appliances like a bulb, tube lights, etc with user clapping action. It is mainly useful for a person who cannot move his legs. The clap switch circuit can be designed in two ways using 555 IC and without using a 555IC.

OBSTACLE DETECTOR

The basic concept of an Infrared Sensor which is used as Obstacle detector is to transmit an infrared signal, this infrared signal bounces from the surface of an object and the signal is received at the infrared receiver.

ENERGY SAVING PROJECT

An energy savings project is a series of activities that involves identifying opportunities to actively reduce energy usage in a building or facility and carrying out a detailed project plan to install and commission energy conservation measures and energy-saving equipment that yield measured improvements in energy

TILT SENSOR

If your car angle changes, the tilt sensor sends a signal to the computer, which activates the alarm. Modern tilt sensors use mercury, which conducts electricity, to monitor a car tilt level. If the car angle suddenly changes, the mercury flows to one side and causes the switch to activate, sounding the alarm.

STATIC MESSAGE ON DOT MATRIX DISPLAY

To display the entire matrix you need to multiplex the columns or the rows. That is, display each column or row one at a time and do it so quickly that all of the columns or rows appear to be visible at the same time.

INTELLIGENT CALL BELL SYSTEM

In this project, we will design and create an automatic bell that rings every 50 minutes for 50 seconds. The LCD screen will also simultaneously display the time. Such a system can be implemented in schools and colleges quite easily. As per the requirement of the institution, the time duration and interval between alarm sounding can be controlled via changing the program source code.

REAL TIME PANTRY SYSTEM USING ZIGBEE MODULE

In this project the microcontroller which forms the heart of the project, plays an important role in establishing communication between transceivers. The microcontroller communicates with Zigbee transceiver and sends the data to the corresponding transceiver.

DIGITAL THERMOMETER USING LCD

The TMP36 temperature sensor works like a diode, i.e. the temperature changes with the change in the voltage at a defined rate. Here, the sensor reading is displayed in the LCD monitor using arduino.

ALCOHOLSENSING AND ALARM SYSTEM

We here propose an alcohol sensing system that measures alcohol intake, displays percentage of alcohol and also sounds an alarm if it is above a particular threshold. Here we use an alcohol sensor circuit along with lcd display and a buzzer alarm.

DIGITAL CLOCK & CALENDER USING LCD(16*2)

When you first upload the code/sketch in arduino uno. A message will pop up on 16×2 character lcd asking to input date (year,month,day) and time(hour,minute). You have to enter the current date and time. Once you input the time and date clock will start working automatically.

LINE FOLLOWER ROBOT

A line follower consists of an infrared light sensor and an infrared LED. It works by illuminating a surface with infrared light; the sensor then picks up the reflected infrared radiation and, based on its intensity, determines the reflectivity of the surface in question.

SELF BALANCING ROBOT

To keep the robot balanced, the motors must counteract the robot falling. This action requires feedback and correcting elements. The feedback element is the MPU6050 gyroscope + accelerometer, which gives both acceleration and rotation in all three axes.

REMOTE CONTROL WIRED ROBOT PROJECT

A remote control robot uses a micro-controller which act as the robot brain. It receives information from sensors and the input portion of the human interface(the remote control itself), decides what to do, then sends commands to the motion systems and the output part of the human interface.

REMOTE CONTROL WIRELESS ROBOT PROJECT(RF MODULE)

The main purpose of the project is to control a robotic vehicle. This can be achieved by using RF technology for remote operation. It uses 8051 series of microcontroller to achieve its desired operation. This system uses push buttons at the transmitting end. With the help of these push buttons, the receiver is able to receive commands. These commands that are sent are used to control the movement of the robot which gives instructions for either to move the robot forward, backward, left or right etc.

FIRE FIGHTING ROBOT

This advanced project allows a user to control a fire fighter robot equipped with water tank and gun remotely wirelessly for extinguishing fires. For this purposes the system uses an Rf remote for remote operation along with rf receive based microcontroller circuit for operating the robotic vehicle and water pump. The rf based remote transfers users commands through rf signals which are received by the receiver circuit. The receiver circuit now decodes the data commands sent. It then forwards it to the microcontroller.

PC CONTROLLED WIRELESS ROBOTIC PICK AND PLACE ARM

In this work we made a Pick and place robot controlled by an Android application.We know that the whole the digital devices in the world are transformed in to Android OS based systems ,as it is more versatile ,flexible and easy to control and it is an open source software.Here The Pick and place robot is controlled wirelessly by an Android application called Blue control through a blue tooth module. The Android OS as well as Arduino software are open source softwares.

FINGER PRINT VOTING SYSTEM

Fingerprint Based Voting Project is a application where the user is recognized by his finger pattern. Since the finger pattern of each human being is different, the voter can be easily authenticated. The system allow the voter to vote through his fingerprint. Finger print is used to uniquely identify the user. The finger print minutiae features are different for each human being. Finger print is used as a authentication of the voters. Voter can vote the candidate only once, the system will not allow the candidate to vote for the second time

FINGER PRINT DOOR LOCK SYSTEM

Biometric door locks use personally identifiable information in lieu of a traditional key. They use a thermal or optical scanner to store the fingerprints of anyone authorized to unlock your door. Once the scanner determines that you are an authorized user, it prompts you to input a PIN to unlock the door.

FINGER PRINT ATTENDANCE SYSTEM

Biometric systems use fingerprints of the employee to verify the identity of the person clocking in and out. The fingerprint of the employee is scanned, the endpoints and intersections of the fingerprint are matched with the record present in the database and accordingly, the access is granted.

FINGER PRINT BASED PATIENT INFORMATION SYSTEM

The Fingerprint Based Patient System was specifically developed for storing, monitoring and analysing the patient medical reports. The system uses the fingerprint scanner for retrieving the patient details from the system. This system will allow users to access hospital’s information anytime.The integrated database, single it TEAM all means lower cost of operation, maintenance and upgrade and a significant reduction in total cost of ownership. This also makes expanding to a new location a breeze as the additional IT investment is minimal.

ELECTRONICS PROJECTS